13.340.20 (Head protective equipment) 标准查询与下载

ASTM F2032-15 BMX自行车用头盔的标准规范

1.1 This specification covers performance requirements for helmets used in BMX cycling. Studies have shown higher risk to the head and face for this sport as compared to recreational street riding; therefore, this specification requires impact protection over a larger area of the head than Specification F1447 and the CPSC standard. This specification also provides performance criteria for helmets equipped with chin bars. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446 except where noted herein. 1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the headgear with faceguard meets all of the requirements of the specification in their entirety. A headgear with faceguard that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be sold with any indication that it meets parts of the specification. 1.4 Headgear designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.5 The values stated in SI units are to be regarded as standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Helmets Used for BMX Cycling

ASTM F1952-15 下坡山地自行车赛用头盔的标准规范

1.1 This specification covers performance requirements for helmets used by downhill mountain bicycle riders. Studies have shown higher risk to the head and face for this sport as compared to recreational street riding; hence, this specification requires greater impact protection and provides performance criteria for chin bars on full-face helmets, but does not require full-face helmets. This specification recognizes the desirability of lightweight construction and ventilation; however, it is a performance specification and is not intended to restrict design. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. 1.3 Partial utilization of this standard is prohibited. Any statement of compliance with this specification must be a certification that the product meets all of the requirements of this specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this standard, and should not be sold with any indication that it meets parts of this standard. 1.4 Headgear designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 The following safety caveat applies to the chemical, mechanical, or physical, or a combination thereof, test methods described herein and is meant specifically for those performing the tests (in an effort to provide them with notice to take the appropriate precautions when conducting the tests): This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Helmets Used for Downhill Mountain Bicycle Racing

ASTM F2713-14 陆上曲棍球用护目器的标准规格

1.1 This specification covers eye protectors with a plano (that is, non-prescription) lens or without a lens, designed for use by players of field hockey, that minimize or significantly reduce injury to the eye and adnexa due to impact by and penetration of field hockey balls and field hockey sticks. Contact with the eye of the headform constitutes failure. Protective eyewear offers protection only to the eyes and does not protect other parts of the head. 1.2 Testing is done in a laboratory setting. Eye contact is determined by observation. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.4 The following precautionary caveat pertains only to the test methods portion (Sections 8, 9, and 10) of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Eye Protectors for Field Hockey

ASTM F3077-14 女子长曲棍球用护目器的标准规格

1.1 This specification covers eye protectors designed for use by players of women’s lacrosse that minimize or significantly reduce injury to the eye and adnexa due to impact and penetration of lacrosse balls. Protective eyewear offers protection only to the eyes and does not protect other parts of the head. 1.2 Impact testing is done in a laboratory setting. Eye contact is determined by observation. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.4 This standard applies to plano eyewear only. 1.5 The following precautionary caveat pertains only to the test methods portion (Sections 8, 9, and 10) of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Eye Protectors for Womenrsquo;s Lacrosse

ASTM F3103-14 越野摩托车和亚视头盔试验的标准规格

1.1 This specification covers performance requirements for helmets used by off-road motorcycle and All-Terrain Vehicle (ATV) riders. 1.2 Compliance with the federally mandated FMVSS No. 218 shall be documented as part of compliance with this ASTM standard. 1.3 This specification provides additional performance requirements including positional stability and performance criteria for chin bars on full-facial coverage helmets if the helmet is equipped with a chin bar. 1.4 This standard does not require that helmets provide full facial coverage. 1.5 This is a performance specification and is not intended to restrict design. 1.6 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. 1.7 Partial utilization of this standard is prohibited. Any statement of compliance with this specification must be a certification that the product meets all of the requirements of this specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this standard, and should not be sold with any indication that it meets parts of this standard. 1.8 Headgear designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.10 The following safety caveat applies to the chemical, mechanical, or physical, or a combination thereof, test methods described herein and is meant specifically for those performing the tests (in an effort to provide them with notice to take the appropriate precautions when conducting the tests): This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Testing Off-Road Motorcycle and ATV Helmets

ASTM F2530-13 骑牛用带面罩的防护头盔的标准规范

1.1 This specification covers performance requirements and describes test methods for protective headgear with faceguards for use in bull riding. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. 1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the headgear with faceguard meets all of the requirements of the specification in their entirety. A headgear with faceguard that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be sold with any indication that it meets parts of the specification. 1.4 Headgear with faceguards designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.5 The values stated in SI units are to be regarded as standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Protective Headgear with Faceguard Used in Bull Riding

ASTM F1446-13 评估防护帽性能特征的设备和程序的标准试验方法

5.1 The purpose of these test methods is to provide reliable and repeatable tests for the evaluation of various types of protective headgear. Use of these test methods in conjunction with the specific individual performance standards is intended to reduce the likelihood of serious injury and death resulting from impacts to the head sustained by individuals participating in sports, recreation, and other leisure activities in which protective headgear is worn. 1.1 These test methods cover laboratory equipment, procedures, and basic requirements pertinent to testing protective headgear. Deviations or additions, or both, to these test methods will be specified, as required, in individual ASTM performance standards. 1.2 Requirements—The protective headgear is to be tested under specified environmental conditions for the following: 1.2.1 Impact attenuation (the limiting of head acceleration) of the protective headgear, and 1.2.2 Strength and stability of the retention system and its attachment to the protective headgear. 1.2.3 Special tests for particular protective headgear uses will be specified in the individual performance standards to be used in conjunction with these test methods. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Equipment and Procedures Used in Evaluating the Performance Characteristics of Protective Headgear

ASTM F2713-13 曲棍球护眼用具的标准规范

1.1 This specification covers eye protectors with a plano (that is, non-prescription) lens or without a lens, designed for use by players of field hockey, that minimize or significantly reduce injury to the eye and adnexa due to impact by and penetration of field hockey balls and field hockey sticks. Contact with the eye of the headform constitutes failure. Protective eyewear offers protection only to the eyes and does not protect other parts of the head. 1.2 Testing is done in a laboratory setting. Eye contact is determined by observation. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.4 The following precautionary caveat pertains only to the test methods portion (Sections 8, 9, and 10) of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Eye Protectors for Field Hockey

ASTM F1446-12 评估防护帽性能特征的设备和程序的标准试验方法

1.1 These test methods cover laboratory equipment, procedures, and basic requirements pertinent to testing protective headgear. Deviations or additions, or both, to these test methods will be specified, as required, in individual ASTM performance standards. 1.2 Requirements???The protective headgear is to be tested under specified environmental conditions for the following: 1.2.1 Impact attenuation (the limiting of head acceleration) of the protective headgear, and 1.2.2 Strength and stability of the retention system and its attachment to the protective headgear. 1.2.3 Special tests for particular protective headgear uses will be specified in the individual performance standards to be used in conjunction with these test methods. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Equipment and Procedures Used in Evaluating the Performance Characteristics of Protective Headgear

ASTM F2220-12 头形的标准规范

1.1 This standard specifies the materials, sizing, and manufacturing details of test headforms for use in the testing of protective headgear. Details of the exterior dimension of the headforms are included. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Specification for Headforms

ASTM F2178-12 测定眼睛或者面部防护产品的耐电弧热性能和标准规范的标准试验方法

1.1 Because of the variability of the arc exposure, different heat transmission values may be observed at individual sensors. The results of each sensor are evaluated in accordance with Section 12. 5.2 This test method maintains the specimen in a static, vertical position and does not involve movement except that resulting from the exposure. 5.3 This test method specifies a standard set of exposure conditions. Different exposure conditions may produce different results. 5.4 This specification covers the minimum performance criteria for arc resistance and other requirements for eye or face protective products used by workers who may be exposed to thermal hazards of momentary electric arcs or flame. 5.5 The purchaser has the option to perform or have performed any of these tests in order to verify the performance of the eye or face protective product. Claims for failure to meet the specification are subject to verification by the manufacturer.Note 1???In addition to the standard set of exposure conditions, other conditions representative of the expected hazard may be used and shall be reported should this data be cited. 1.1 This test method and product specification is used to measure the arc rating and specify the requirements for products intended for use as eye or face protection for workers exposed to electric arcs that would generate heat flux values from 84 to 258201;120 kW/m28201;[2 to 600 cal/cm2s]. Products are tested as sold. 1.2 This test method determines an arc rating for eye or face protective products. The faceshield, safety spectacle, goggle or or other applicable portions of the complete product must meet ANSI Z87.1. This excludes the textile or non ANSI Z87.1 testable parts of the hood assemblies or other tested products. This standard does not measure optical and impact properties (see ANSI Z87.1) but does specify requirements for optical and impact properties. 1.3 The materials covered by this standard are in the form of faceshields attached to the head by protective helmets (hard hats), headgear, hood assemblies, safety spectacles or goggles. Faceshields, safety spectacles or goggles are tested with or without other face and head protective products, for example, sock hoods, balaclavas, sweat shirt hoods or jacket hoods.

Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products

ASTM F2812-12 选定的汽车运动的护目镜和眼镜型防护眼镜的标准规范

1.1 This specification covers eye protectors, exclusive of helmet-mounted visors, designed for use by riders of motorcycles, mopeds, and snowmobiles for off road use that minimize or significantly reduce injury to the eye and adnexa as a result of impact and penetration by objects that may be kicked up from the road, track, trail, or snow surfaces and made airborne and, as such, likely to cause eye discomfort or injury. This specification does not address shield-type eye protectors such as are connected to, integral to, and/or supported by protective helmets. Protective eyewear offers protection only to the eyes and does not protect other parts of the head, face, or neck. 1.2 Protectors are divided into two types, goggles or spectacles, depending on their design characteristics. 1.3 This specification does not apply to prescription eyewear. (Warning???Impact-resistant prescription spectacles that conform to the standard specifications of ANSI Z87.1 should be used if spectacles are to be worn under goggle-type eyewear as covered by this specification.) 1.4 In this specification, the use of the word ???shall??? indicates a mandatory requirement. The word ???should??? indicates a recommendation. 1.5 Units???The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measure in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Goggle- and Spectacle-Type Eye Protectors for Selected Motor Sports

ASTM F1446-11 用于评估防护头盔性能特征的设备和程序的标准测试方法

The purpose of these test methods is to provide reliable and repeatable tests for the evaluation of various types of protective headgear. Use of these test methods in conjunction with the specific individual performance standards is intended to reduce the likelihood of serious injury and death resulting from impacts to the head sustained by individuals participating in sports, recreation, and other leisure activities in which protective headgear is worn.1.1 These test methods cover laboratory equipment, procedures, and basic requirements pertinent to testing protective headgear. Deviations or additions, or both, to these test methods will be specified, as required, in individual ASTM performance standards. 1.2 Requirements8212;The protective headgear is to be tested under specified environmental conditions for the following: 1.2.1 Impact attenuation (the limiting of head acceleration) of the protective headgear, and 1.2.2 Strength and stability of the retention system and its attachment to the protective headgear. 1.2.3 Special tests for particular protective headgear uses will be specified in the individual performance standards to be used in conjunction with these test methods. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Equipment and Procedures Used in Evaluating the Performance Characteristics of Protective Headgear

ASTM F2530-11 骑牛用带面罩的防护头盔标准规范

1.1 This specification covers performance requirements and describes test methods for protective headgear with faceguards for use in bull riding. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. 1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the headgear with faceguard meets all of the requirements of the specification in their entirety. A headgear with faceguard that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be sold with any indication that it meets parts of the specification. 1.4 Headgear with faceguards designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.5 The values stated in SI units are to be regarded as standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Protective Headgear with Faceguard Used in Bull Riding

ASTM F1446-11a 评定安全防护帽功能特性用设备和程序的标准试验方法

The purpose of these test methods is to provide reliable and repeatable tests for the evaluation of various types of protective headgear. Use of these test methods in conjunction with the specific individual performance standards is intended to reduce the likelihood of serious injury and death resulting from impacts to the head sustained by individuals participating in sports, recreation, and other leisure activities in which protective headgear is worn.1.1 These test methods cover laboratory equipment, procedures, and basic requirements pertinent to testing protective headgear. Deviations or additions, or both, to these test methods will be specified, as required, in individual ASTM performance standards. 1.2 Requirements8212;The protective headgear is to be tested under specified environmental conditions for the following: 1.2.1 Impact attenuation (the limiting of head acceleration) of the protective headgear, and 1.2.2 Strength and stability of the retention system and its attachment to the protective headgear. 1.2.3 Special tests for particular protective headgear uses will be specified in the individual performance standards to be used in conjunction with these test methods. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Equipment and Procedures Used in Evaluating the Performance Characteristics of Protective Headgear

ASTM F659-10 雪橇滑雪和单板滑雪用护目镜标准规范

1.1 This specification covers the minimal requirements of ski and snowboard goggles (intended for nonmotorized use) to provide a reasonable degree of protection against snow and moisture striking or lodging in the eye or surrounding soft tissue. 1.2 The scope of this specification shall include requirements for materials, optical properties, lens strength and retention, labeling, identification, and testing procedures. 1.2.1 Contact lenses, sunglasses, and corrective dress eye wear are not included within the scope of this specification. (Warning8212;Impact resistant prescription spectacles that conform to the standard specifications of ANSI Z87.1 should be used if spectacles are to be worn under goggle-type eyewear as covered by this specification.) 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Ski and Snowboard Goggles

ASTM F2713-09 曲棍球护眼用具的标准规范

1.1 This specification covers eye protectors, designed for use by players of field hockey that minimize or significantly reduce injury to the eye and adnexa due to impact by and penetration of field hockey balls and field hockey sticks. Contact with the eye of the headform constitutes failure. Protective eyewear offers protection only to the eyes and does not protect other parts of the head. 1.2 Impact testing is done in a laboratory setting. Eye contact is determined by observation. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.4 The following precautionary caveat pertains only to the test methods portion (Sections 8, 9, and 10) of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Eye Protectors for Field Hockey

ASTM F2727-09 标识头饰产品的制造商的标准指南

This guide gives guidelines for labels and instructions to manufacturers of non-motorized sports and recreation headgear. The purpose of the labels and instructions is to help alert and remind headgear users of important issues related to headgear and its use. Limitation8212;This guide applies only to protective headgear whose standard specifications are under auspices of ASTM Committee F08.1.1 This guide sets forth labeling and instruction guidelines for manufacturers of headgear for non-motorized sports and recreation. 1.2 This guide applies only to protective headgear whose standard specifications are under auspices of ASTM Committee F08. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Manufacturers for Labeling Headgear Products

ASTM F1952-09 下坡山地自行车赛用头盔的标准规范

1.1 This specification covers performance requirements for helmets used by downhill mountain bicycle riders. Studies have shown higher risk to the head and face for this sport as compared to recreational street riding; hence, this specification requires greater impact protection and provides performance criteria for chin bars on full-face helmets, but does not require full-face helmets. This specification recognizes the desirability of lightweight construction and ventilation; however, it is a performance specification and is not intended to restrict design. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F 1446, except where noted herein. 1.3 Partial utilization of this standard is prohibited. Any statement of compliance with this specification must be a certification that the product meets all of the requirements of this specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this standard, and should not be sold with any indication that it meets parts of this standard. 1.4 Headgear designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Helmets Used for Downhill Mountain Bicycle Racing

ASTM F2397-09 军体运动中使用的防护安全帽标准规范

1.1 This specification covers performance requirements for head protection used for training and competition in martial arts such as karate, wushu, and taekwondo, where normal contact between participants may be repeated, but is limited to a level that is not intended to produce injury. These activities typically take place in indoor or outdoor environments where the temperature is moderate. This specification recognizes the desirability of a lightweight and streamlined construction, and ventilation; however it is a performance specification, and is not intended to restrict design. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted in this specification. 1.3 Partial utilization of this standard is prohibited. Any statement of compliance with this specification shall be a certification that the product meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be distributed or sold with any indication that it meets parts of the specification. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 The following safety caveat applies to the chemical, mechanical, or physical, or a combination thereof, test methods described herein and is meant specifically for those performing the tests (in an effort to provide them with notice to take the appropriate precautions when conducting the tests): This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Protective Headgear Used in Martial Arts