共找到 1487 条与 手工工具 相关的标准,共 100 页
Socket wrenches-Part 2:6.3∼25 mm square drive
Nipper for the use of jewel-setting and fine wire-cutting
Socket wrenches-Part 1:12.7 mm square drive
Socket wrenches with hexagon drive extension for hexagon bolts, machine operated
Double offset screwdrivers for cross point screws
Part 2-2 of this European Standard specifies requirements, limiting dimensions and operating forces for hand crimping tools with removable and interchangeable dies, sizes A to G, Q to T,V and W, for the termination of cables to radio frequency connectors.
Hand crimping tools - Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications - Part 2-2: Particular requirements for radio frequency connectors and concentric contacts - Open throat tools with remov
Hand crimping tools - Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications -- Part 2-2: Particular requirements for radio frequency connectors and concentric contacts - Open throat tools with remo
Hand-held motor-operated electric tools - Safety - Part 2-23: Particular requirements for die grinders and small rotary tools (First Edition; Update No 1: April 2015)
Single-head wrenches for lower torque applications. Widths of heads. Basic parameters
Double-ended open-ended wrenches, double-headed box and combination. Widths of heads. Basic dimensions
This Standard specifies the maximum outside head dimensions for double-headed open-ended wrenches, double-headed ring wrenches and combination wrenches, identified in GSO ISO 1703 under reference Nos. 1 1 01 02 0, 1 1 01 05 0, 1 1 01 06 0, 1 1 02 03 0, 1 1 02 04 0, 1 1 02 05 0, 1 1 02 06 0.
Assembly tools for screws and nuts - Double-headed open-ended wrenches, double-headed box wrenches and combination wrenches - Maximum widths of heads
This International Standard specifies characteristics of single-head engineer's wrenches with gaps from 7 mm to 120 mm, listed in GSO ISO 1703 under the reference Nos. 1 1 01 01 0 and 1 1 01 01 1. The “lower torque application” designation is in accordance with the smaller head dimensions. Essentially, this International Standard establishes the first specifying maximum outside dimensions of heads and gives the test torque values, which are calculated on the basis of approximately half the values, in accordance with GSO ISO 1711-1, series C.
Assembly tools for screws and nuts - Single-head engineer's wrenches for lower torque applications - Maximum outside dimensions of heads and test torques
This Standard prescribes the technical specifications for square drive adaptor hexagon or cylindrical flat inserts for power socket wrenches. It applies to square drive adaptors with hexagon drive or with cylindrical flat end drive as defined in GSO ISO 1173, and to driving squares for power socket wrenches as defined in GSO ISO 1174-2. Square drive adaptors with hexagon drive, for power socket wrenches, are listed under number 5 2 00 02 0 in GSO ISO 1703.
Assembly tools for screws and nuts - Square drive adaptor with hexagon or cylindrical flat drive, for power socket wrenches
本部分规定了高枝剪的产品分类、要求、试验方法、检验规则及标志、包装、运输、贮存。本部分适用于修整各种树枝、采集树种等用途的高枝剪。
Garden tools.Long-reach pruners
本部分规定了手用和机用一字槽螺钉旋具旋杆的产品分类、要求和试验方法。本部分适用于手用和机用一字槽螺钉旋具旋杆(以下简称“旋杆”)。
Screwdrivers.Screwdriver blades for slotted head screws
本部分规定了稀果剪的产品分类、要求、试验方法、检验规则及标志、包装、运输、贮存。本部分适用于修剪各种果树、采摘葡萄、棉花整枝等用途的稀果剪。
Garden tools.Fruit scissors
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号