共找到 275 条与 电阻器综合 相关的标准,共 19 页
This drawing describes the requirements for fixed, electrolytic, double layer, sealed, high-reliability capacitors.
CAPACITORS, FIXED, ELECTROLYTIC, DOUBLE LAYER, SEALED
This CID covers the general requirements for a non-linear thermistor, commonly called resettable fuses. These resistors are polymeric positive temperature coefficient devices that offer a wider voltage, current and temperature range. Requirements for specific resistors are covered in the individual CID sheets. The resistors covered by this CID are intended for commercial/industrial applications.
RESISTORS, THERMAL, NON-LINEAR THERMISTOR (RESETTABLE FUSES) GENERAL REQUIREMENTS FOR
This drawing describes the requirements for a bulk metal foil, ultra precision, chip resistor.
RESISTOR, FIXED, BULK METAL FOIL, CHIP, ULTRA PRECISION, STYLE 1505
This supplement forms a part of MIL-PRF-20K, dated 14 November 2003.
CAPACITOR, FIXED, CERAMIC DIELECTRIC (TEMPERATURE COMPENSATING), ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
This specification covers the general requirements for established reliability (ER) and non-ER, emperature compensating, fixed capacitors for use primarily where compensation is necessary for circuitapplications due to temperature changes, in bypass and coupling applications. Capacitors meeting the ER requirements specified herein have a failure rate level (FRL) ranging from 1.0 percent per 1,000 hours to 0.00l percent per 1,000 hours. These failure rate levels are established at a 90-percent confidence level based on the life test parameters specified and are maintained at a 10-percent producer's risk. An acceleration factor of 8:1 has been used to relate the life test data at 200 percent of rated voltage at the applicable high test temperature to the rated voltage at the applicable high test temperature. A part per million (ppm) quality system is used for documenting and reporting the average outgoing quality of ER capacitors supplied to this specification. Statistical process control (SPC) techniques are required in the manufacturing process to minimize variation in production of ER capacitors supplied to the requirements of this specification.
CAPACITOR, FIXED, CERAMIC DIELECTRIC (TEMPERATURE COMPENSATING), ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
This drawing describes the requirements for a 0.040 x 0.020 chip resistor.
RESISTOR, CHIP, FIXED, FILM, STYLE 0402
This drawing describes the requirements for a 0.030 x 0.020 chip resistor.
RESISTOR, CHIP, FIXED, FILM, STYLE 0302
The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at www.dodssp.daps.mil.
FILTERS AND CAPACITORS, RADIO FREQUENCY INTERFERENCE, GENERAL SPECIFICATION FOR
This specification covers the general requirements for molded and dipped mica dielectric, fixed capacitors intended primarily for use in high-stability, low-loss radio-frequency applications such as tuned circuits (see 6.1). This is a graded specification covering ranges in temperature oefficient, capacitance, tolerance, temperature, and vibration.
CAPACITORS, FIXED, MICA DIELECTRIC, GENERAL SPECIFICATION FOR
This drawing describes the requirements for a 20 pin, hermetically sealed, dual-in-line package (DIP) resistor network.
RESISTOR NETWORK, FIXED, FILM, 20 PIN, HERMETICALLY SEALED, DUAL-IN-LINE PACKAGE (DIP)
This drawing describes the requirements for insulated, fixed, film, resistor available in F (±1 percent), G (±2 percent), J (±5 percent), and K (±10 percent) resistance tolerances. These resistors are capable of full-load operation at an ambient temperature of 70OC.
RESISTORS, FIXED, FILM (INSULATED), 2 WATT
This drawing describes the requirements for a 20 pin, leadless chip carrier, resistor network. These networks are available only in nonhermetically sealed packages.
RESISTOR NETWORK, FIXED, FILM, SURFACE MOUNT, 20 PIN, LEADLESS CHIP CARRIER
This drawing describes the requirements for a 16 pin, leadless chip carrier, resistor network. These networks are available in hermetically sealed and nonhermetically sealed packages.
RESISTOR NETWORK, FIXED, FILM, SURFACE MOUNT, 16 PIN, LEADLESS CHIP CARRIER
This drawing describes the requirements for a 20 pin, leadless chip carrier, resistor network. These networks are available in hermetically sealed and nonhermetically sealed packages.
RESISTOR NETWORK, FIXED, FILM, SURFACE MOUNT, 20 PIN, LEADLESS CHIP CARRIER
This drawing and MIL-PRF-28861describes the complete requirements for radio requency/electromagnetic interference suppression, hermetically sealed, filters and capacitors
FILTERS AND CAPACITORS, RADIO FREQUENCY/ELECTROMAGNETIC INTERFERENCE SUPPRESSION, HERMETICALLY SEALED
This specification covers the requirements for high reliability, discoidal, ceramic dielectric, fixed capacitors. This specification provides for two levels of product requirements: Class B and class S. Capacitors furnished to the requirements of this specification are intended for use in Radio Frequency/ Electromagnetic Interference (RFI/EMI) suppression filters covered by MIL-PRF-28861. This specification establishes a Qualified Manufacturers List (QML) for discoidal capacitors that requires demonstration of control of the quality system and manufacturing process and qualification of representative discoidal capacitor designs.
CAPACITORS, FIXED, CERAMIC DIELECTRIC, HIGH RELIABILITY, DISCOIDAL, GENERAL SPECIFICATION FOR
This drawing describes the requirements for a fixed, film, chip, .200 X .125, 1/8 watt, precision resistor.
RESISTOR, FIXED, FILM, PRECISION, CHIP 1/8 WATT, STYLE 2012
This drawing describes the requirements for a precision, fixed, film, resistor.
RESISTOR, FIXED, FILM, PRECISION
This drawing describes the requirements for a resistor network, fixed, film, small outline, 14 pin, supplied to the requirements of MIL-PRF-914/1 except as noted herein.
RESISTOR NETWORK, FIXED, FILM, SURFACE MOUNT, GULL WING, 14 PIN
This drawing describes the requirements for a fixed, film, chip resistor (melf) 0.120 X 0.060.
RESISTOR, FIXED, FILM, CHIP (MELF), 1/8 WATT, STYLE 1206
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号