31.040.01 电阻器综合 标准查询与下载

DLA DSCC-DWG-88016 REV B-2000 20引脚单列直插式封装电阻网络

This drawing describes the requirements for a 20 pin, leadless chip carrier, resistor network with multiple resistance values and tolerances.

RESISTOR NETWORKS, FIXED, FILM, 20 PIN, LEADLESS CHIP CARRIER

DLA DSCC-DWG-87031 REV D-2000 单列直插式封装8引脚的电阻网络

This drawing describes the requirements for a 8 pin, single-in-line, resistor network.

RESISTOR, NETWORK, 8 PIN, SINGLE-IN-LINE PACKAGE (SIP)

DLA DSCC-DWG-88036 REV A-2000 10引脚无引线芯片座电阻网络

This drawing describes the requirements for a 10 pin, leadless chip carrier, resistor network.

RESISTOR NETWORK, 10 PIN, LEADLESS CHIP CARRIER

DLA DSCC-DWG-88020 REV B-2000 6引脚无引线芯片座电阻网络

This drawing describes the requirements for a 6-pin, leadless chip carrier, resistor network.

RESISTOR NETWORK, 6-PIN, LEADLESS CHIP CARRIER

DLA DSCC-DWG-87027 REV C-2000 3个引脚涂膜固定电阻网络

This drawing describes the requirements for a fixed, film, 3-pin resistor network.

RESISTOR NETWORK, FIXED, FILM, 3-PIN

DLA DSCC-DWG-92013 REV A-2000 固定10PIN SIP延长引线长度电阻器网络

This drawing describes the requirements for a 10 pin, single in line package (SIP), resistor network with a ±100 ppm/°C temperature coefficient.

RESISTOR NETWORKS, FIXED, FILM, 10 PIN, SIP, EXTENDED LEAD LENGTH

DLA DSCC-DWG-88040 REV D-2000 变量表面安装非线绕修整电阻器

This drawing describes the requirements for a variable, surface mount, non-wirewound (adjustment type, lead screw actuated) resistor.

RESISTOR, VARIABLE, SURFACE MOUNT, NON-WIREWOUND, TRIMMER

DLA A-A-59496-2000 绕有电阻丝或没绕的匀货机微调电容器调整片 可变电阻 常规

This CID covers the general requirements for variable, nonwire wound, wire wound, single turn, multi-turn and lead-screw actuated, with a contact bearing uniformly over the entire surface of the entire resistive element, when positioned by an actuator. These resistors are capable of full load operation at maximum temperatures, and are suitable for continuous operation when properly derated. Requirements for specific resistors are covered in the individual CID sheets.

RESISTOR, VARIABLE, TRIMMER NONWIRE WOUND, AND WIREWOUND, GENERAL SPECIFICATION FOR

DLA A-A-59497-2000 非精确或精确的绕线或没绕线可变电阻 常规

This CID covers the general requirements for wire wound, nonwire wound, precision, nonprecision variable resistors. The individual requirements for specific resistors are covered in the individual CID sheets. For technical assistance when utilizing parts for parameters not specifically detailed, contact the manufacturers listed on applicable CID sheets. The resistors covered by this CID are intended for commercial/industriaI applications.

RESISTORS, VARIABLE, NONWIRE WOUND, WIRE WOUND, PRECISION, NONPRECISION, GENERAL REQUIREMENTS FOR

DLA DSCC-DWG-88022 REV C-2000 固定极化电解质氧化铝及单端安装的电容器

This drawing and MIL-PRF-39018 describes the complete requirements for aluminum oxide, electrolytic capacitors.

CAPACITORS, FIXED, ELECROLYTIC, POLARIZED, ALUMINUM OXIDE, SINGLE END MOUNTING

ARMY MS24537 REV C VALID NOTICE 3-2000 24伏特直流电电阻温度变送器

MS24537C remains inactive for new design, however, the document is valid for acthewhen needed.

TRANSMITTER, TEMPERATURE ELECTRICAL RESISTANCE - 24 VOLT DC

ARMY MS24543 REV H VALID NOTICE 2-2000 24伏特直流电.范围在120度至零下240度的电阻温度变送器

MS24543H remains inactive for new design, however, the document is valid for acthewhen needed.

INDICATOR, TEMPERATURE, ELECTRICAL RESISTANCE; 24 VOLT DC, RANGE 120 DEG. -240 DEG. F

ARMY MS24542 REV H VALID NOTICE 2-2000 24伏特直流电.范围在160度至零下320度的电阻温度变送器

MS24542H remains inactive for new design, however, the document is valid for acthewhen needed.

INDICATOR, TEMPERATURE, ELECTRICAL RESISTANCE; 24 VOLT DC, RANGE 160 DEG.-320 DEG. F

NAVY MIL-G-7818 (2)-1999 补偿式电容器燃油量应变计

This amendment fomis a part of MIL-G-78 18, dated 26 November 195 1, and is approved for use by all Departments and Agencies of the Department of Defense.

GAGE, FUEL QUANTITY, CAPACITOR TYPE, COMPENSATED, GENERAL SPECIFICATION FOR

JB/T 8622-1997 工业铂热电阻技术条件及分度表

本标准适用于－200℃～＋850℃整个或部分温度范围的工业铂热电阻。

Technical specification and reference table for industrial platinum thermal resistance

DLA DSCC-DWG-89040 REV B-1997 固定线绕表面安装功率性(2.5瓦特)电阻器

This drawing describes the requirements for a surface mounted, fixed, power type, wire wound and low value shunt wire resistor.

RESISTOR, FIXED, WIRE WOUND, SURFACE MOUNT, POWER TYPE (2.5 WATTS)

NAVY MIL-DTL-15024 F-1997 设备识别的电容器板,标签和传送带总说明书

This performance specification covers the physical characteristics of plates, tags and bands (identification devices) used for identification of equipment. Examples of information to be marked on the identification devices are covered in the applicable specification sheets.

PLATES, TAGS, AND BANDS FOR IDENTIFICATION OF EQUIPMENT, GENERAL SPECIFICATION FOR

SJ 20603-1996 片式电阻器用电阻浆料规范

Specification for resistance paste for use in chip resistors

UL 1676-1995 放电电路电阻器

Discharge path resistors

DLA DESC-DWG-87030 REV C-1993 单列直插式封装6针网络电阻器网络

This revision described below has been authorized for the document listed.

RESISTOR, NETWORK, 6-PIN, SINGLE-IN-LINE PACKAGE