J45 组合卡具 标准查询与下载

DIN 9832:1996 冲压工具.导套座

Holders according to this document are used for guide bushes according to DIN 9831-1, DIN 9831-2 and DIN 9834, and for guide posts according to DIN 9825-3, DIN 9825-4 and DIN 9833.#,,#

Tools for pressing - Holder for guide bushes

JB/T 8335-1996 孔系列组合夹具元件 分类编号规则

Classification and numbering rules for hole series combined fixture components

JIS B 2809:1996 钢丝绳.钢丝绳或钢丝绞合线用夹子

この規格は，ワイーやロープ又は鋼より線(steel wire strand)の締付けに用いるワイヤグリップ(以下，グリップという。)について規定する。

Wire ropes -- Grips for rope or wire strand

HB 7147.5-1995 大型系列组合夹具压紧件 弯头压板

Large series combined clamp pressing parts Bent-head clamp plate

HB 7147.6-1995 大型系列组合夹具压紧件 齿纹弯头压板

Large series combined clamp pressing parts Indented bent-head clamp plate

HB 7147.7-1995 大型系列组合夹具压紧件 基础板用弯头压板

Large series combined clamp pressing parts Bent-head clamp plate for baseplate

HB 7147.4-1995 大型系列组合夹具压紧件 摆动压板

Large series combined clamp pressing parts Swinging clamp plate

HB 7147.1-1995 大型系列组合夹具压紧件 平压板

Large series combined clamp pressing parts Flat clamp plate

HB 7147.2-1995 大型系列组合夹具压紧件 伸长压板

Large series combined clamp pressing parts Extension clamp plate

HB 7147.3-1995 大型系列组合夹具压紧件 回转压板

Large series combined clamp pressing parts Slewing clamp plate

HB 7147.8-1995 大型系列组合夹具压紧件 大头叉形压板

Large series combined clamp pressing parts Large head forked clamp plate

HB 7147.9-1995 大型系列组合夹具压紧件 宽头叉形压板

Large series combined clamp pressing parts Broad head forked clamp plate

DIN 6345:1995 工具夹紧用带夹紧片的筒夹用夹紧装置

Holding fixtures for collets dead length type with clamping lamellas are used for the clamping of tools.

Holding fixtures for collets dead length type with clamping lamellas for the clamping of tools

SN/T 0360-1995 出口弹簧夹头检验规程

Rules for inspection of colletfor export

JB/T 7449-1994 槽系列组合冲模元件 分类编号规则

Classification and numbering rules for combination die components of groove series

JB/T 7180-1994 槽系列组合夹具元件.通用技术条件

本标准规定了6mm、8mm、12mm和16mm槽系列组合夹具元件的技术要求，标志与包装。 本标准适用于槽系列组合夹具各类元件的设计、制造与成品验收。

Components of slot series combination clamps General technical conditions

JB/T 7450-1994 组合夹具经济效益评估方法

本标准规定了使用组合夹具经济效益的评估方法。 本标准适用于各单位对使用组合夹具的经济效益进行分析和估算。

Assessment method for economic benefit of modular fixtures

ASTM F1025-94(2006) 用于增强或修复聚乙烯煤气压力管上爆裂或破洞的全环绕型带夹紧装置的选择和使用

Full-encirclement-type band clamps are recommended for repairs only where the pipe is able to maintain its structural integrity. These clamps are not recommended for permanent repair of pipe where the damage could propagate outside the clamp under anticipated field conditions (see 5.1.1 for repair limitations). In such situations, cut out and replace the damaged pipe with a new piece. These clamps may be used to cover holes left in the pipe from abandoned service line connections, purge points, and accidental punctures. These clamps may be used to reinforce the pipe where the wall thickness has been reduced because of gouges or other irregularities. Some users reinforce polyethylene pipe after it has been squeezed-off as a precaution against pipe damage that may have occurred during the squeeze-off process and as a means of ensuring that the pipe will not be squeezed-off again at the same location. Consult with the polyethylene pipe manufacturer as to the appropriateness of squeeze-off for their product, and for circumstances when reinforcement is recommended. See Guide F 1041. 1.1 This guide specifically addresses the design and installation of full-encirclement-type band clamps for repair of gouges, punctures, or holes, and for reinforcement of polyethylene plastic pipe. Guidelines are provided for selecting and using clamps in pipe sizes 2 in. nominal (60 mm) and larger.1.1.1 A test method is also provided for the user to assess the applicability of the repair clamp. Under appropriate circumstances, this type of clamp offers a convenient, effective, and safe means of restoring the integrity of an in-service pipeline, without cutting out a section of pipe (see Note 0). The pipe to be repaired cannot be backed by a stiffener for internal support and cross-sectional dimensional control. Satisfactory use of this type of clamp must rely on the crush resistance of the pipe itself and a fitting design concept, which retains the cross-sectional pipe configuration while minimizing compressive forces required to obtain an effective leakage seal. Note 0The appropriateness for use of this type of clamp should be determined by using the information contained in this guide and from consultation with, and recommendations of, both the pipe and clamp manufacturers. The basic premise for use of this type of clamp is that it is recommended by the manufacturer for this specific application and that step-by-step installation instructions are available for that application. It is important in the development of this type of clamp that prototype testing be conducted to evaluate performance expectations because of the physical limitations encountered when designing it for use with plastic pipe. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe

JB/T 2814-1993 槽系列组合夹具元件分类编号规则

Classification and numbering rules for slot series combined fixture components

DIN 9825-3:1993 K型冲压模架用导柱

Guide pillars according to the document are used for press tool sets with slideway and anti-friction guideway.

Guide pillars for press tool sets; type K