J94 燃油供给系统 标准查询与下载

ISO 14681:1998 柴油机 燃料喷射泵试验 燃料喷射器的校正

This International Standard specifies two types of calibrating injectors intended for testing and setting diesel fuel injection pumps on test benches. It applies to a) calibrating injectors for different orifice plates, max. delivery range 400 mm/stroke; b) calibrating injectors with pintle type nozzle, max. delivery range 200 mm/stroke. The field of application is similar to the calibrating injectors specified in ISO 7440-1 and to the calibrating nozzle specified in ISO 4010. Compared to the calibrating injector specified in ISO 7440-1, the calibrating injectors specified in this International Standard represent an advanced stage of design which is more appropriate to modern high pressure/high performance fuel injection systems. Specification of the type of calibrating fuel injectors to be used, the appropriate single hole orifice plate size or pintle nozzle (as applicable), high pressure pipes, exact limits, etc. is left to the manufacturer of the injection equipment and/or the manufacturer of the engine.

Diesel engines - Fuel injection pump testing - Calibration fuel injectors

KS B 6279-1998 带式输送机带轮

이 규격은 주로 분산물(광석, 토사, 석탄, 시멘트, 곡물 등)을 운반하기 위하여 사용하는

Pulleys for belt conveyors

BS 7403-2:1998 用于内燃机的全流式润滑油过滤器 元件旁通阀特性的试验方法

This part of ISO 4548 specifies tests for determining the element by-pass valve characteristics of full-flow lubricating oil filters for internal combustion engines. Tests are specified with oils at two viscosities, one to assess the performance of an element by-pass valve with a cold oil and the other to assess its performance with an oil at a typical operating temperature.

Full-flow lubricating oil filters for internal combustion engines. Method of test for element by-pass valve characteristics

BS ISO 13296:1998 柴油发动机.高压燃料注射管道组件.一般要求和尺寸

Diesel engines - High pressure fuel injection pipe assemblies - General requirements and dimensions

BS ISO 7879:1998 柴油发动机.托架安装直列式燃料喷射泵.安装尺寸

This International Standard specifies the dimensional requirements of cradle-mounted in-line fuel injection pumps for compression-ignition (diesel) engines.

Diesel engines - Cradle mounted in-line fuel injection pumps - Mounting dimensions

BS ISO 7026:1998 柴油发动机.针栓式喷嘴的20,21,21.1和27型拧入式喷嘴座"S1"号"B"型

This International Standard specifies dimensional requirements for the mounting of injection nozzle holders in compression-ignition (diesel) engines. The location of the fuel inlet and leak-off connections are not defined since they vary according to the particular application. This International Standard applies to screw-in injection nozzle holders of types 20, 21, 21.1 and 27. These nozzle holders are used with the pintle nozzle size “S”, type “B”, specified in ISO 2697 1).

Diesel engines - Screw-in injection nozzle holders, types 20, 21, 21.1 and 27 for pintle nozzle size 'S1' type 'B'

BS 7403-1:1998 用于内燃机的全流式润滑油过滤器 压差/流量特性的测试方法

This part of ISO 4548 specifies tests for determining the differential pressure/flow characteristics of full-flow lubricating oil filters for internal combustion engines. Tests are specified with oils at two viscosities, one to assess the performance of a filter with a cold oil and the other to assess its performance with an oil at a typical operating temperature.

Full-flow lubricating oil filters for internal combustion engines. Methods of test for differential pressure/flow characteristics

BS 7403-4:1998 用于内燃机的全流式润滑油过滤器 初始颗粒截留效率、寿命和累积效率的测试方法（重量法）

This part of ISO 4548 specifies tests for determining the performance of full-flow lubricating oil filters for internal combustion engines as follows. Section 2: Initial particle retention efficiency. This gives the test procedures and parameters for the determination of the initial particle retention efficiency of lubricating oil filter elements under defined test conditions. By reporting the results in accordance with subclause 2.6, the probable retention efficiency for any particle size may be derived. The retention efficiency is determined by the gravimetric method. Section 3: Life and cumulative efficiency. This gives the test procedures and parameters for the determination of element life and cumulative efficiency of lubricating oil filters. The cumulative efficiency is determined by the gravimetric method. NOTE —By agreement between filter manufacturer and purchaser, tests on large filters can be conducted on the basis of tests carried out on filters scaled-down in length. The relationship of the filter flow and test dust addition rate to the effective length of the filter medium should be the same in the scaled-down tests as in the full size filter. For the purposes of this part of ISO 4548, a filter having a test flow rate exceeding 100 l/min is considered large.

Full-flow lubricating oil filters for internal combustion engines. Methods of test for initial particle retention efficiency, life and cumulative efficiency (gravimetric method)

ASTM D6278-98 使用欧洲柴油机喷射装置测定含液体聚合物的剪切稳定性的标准试验方法

1.1 This test method covers the evaluation of the shear stability of polymer-containing fluids. The test method measures the percent viscosity loss at 100186C of polymer-containing fluids when evaluated by a diesel injector apparatus procedure that uses European diesel injector test equipment. The viscosity loss reflects polymer degradation due to shear at the nozzle. Note 1-Test Method D 2603 has been used for similar evaluation of shear stability; limitations are as indicated in the significance statement. No detailed attempt has been undertaken to correlate the results of this test method with those of the sonic shear test method. Note 2-This test method uses test apparatus as defined in CEC L-14-A-93. This test method differs from CEC-L-14-A-93 in the period of time required for calibration. Note 3-Test Method D5275 also shears oils in a diesel injector apparatus but may give different results. Note 4-This test method has different calibration and operational requirements than Test Method D 3945. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.

Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus

ISO 7026:1997 柴油机 S尺寸轴针式喷油嘴偶件B型拧入式喷嘴器件(20、21、21.1和27型)

This International Standard specifies dimensional requirements for the mounting of injection nozzle holders in compression-ignition (diesel) engines. The location of the fuel inlet and leak-off connections are not defined since they vary according to the particular application. This International Standard applies to screw-in injection nozzle holders of types 20, 21, 21.1 and 27. These nozzle holders are used with the pintle nozzle size "S", type "B", specified in ISO 2697. note: 1) ISO 2697:1974, Road vehicles — Fuels injection nozzles — Size "S".

Diesel engines - Screw-in injection nozzle holders, types 20, 21, 21.1 and 27 for pintle nozzle size "S", type "B"

ISO 13296:1997 柴油机 高压燃料喷射管组件 一般要求和尺寸

Diesel engines - High-pressure fuel injection pipe assemblies - General requirements and dimensions

BS 7881:1997 汽油过滤器试验方法

Describes three methods of test for petrol filters intended for automotive and marine internal combustion engines.

Method of test for petrol filters

SAE J1696-1997 标准燃油滤油器试验流体

This SAE Standard defines the requirements for fluid to be used in the SAE Fuel Filter Test Procedures.

Standard Fuel Filter Test Fluid

ANSI/ANS 59.51-1997 应急柴油发电机的燃油系统

This standard provides functional, performance, and initial design requirements for the fuel oil system for diesel generators that provide safety-related emergency onsite power for light water reactor nuclear power plants. This standard addresses the mechanical equipment associated with the fuel oil system, with the exception of the engine mounted components. These components, which are mounted directly to the engine structure itself, are excluded except to define interface requirements. It also includes the instrumentation and control functional requirements.

Fuel-Oil Systems for Emergency Diesel Generators

ISO 8535-1:1996 压燃式发动机 高压燃油喷管用钢管 第1部分:无缝冷拔单壁管的要求

Specifies dimensions and requirements for seamless cold-drawn single-wall steel tubes for high-pressure fuel injection pipes on diesel engines (Class 2) and for fuel injection pump testing (Class 1). Replaces the second edition.

Compression-ignition engines - Steel tubes for high-pressure fuel injection pipes - Part 1: Requirements for seamless cold-drawn single-wall tubes

JIS S 3030:1996 燃油装置结构通则

General rules for construction of oil burning appliances

JIS S 3031:1996 燃油装置试验方法通则

General rules for test methods of oil burning appliances

BOCA CHAPTER 32 NFPC-1996 易燃和可燃液体

The format and provisions of The BOCA National Propero Maintenance Code are designed to provide units of government with an effective regulatory means of providing minimum health and safety requirements for existing buildings and structures.

Flammable and Combustible Liquids

KS B 6278-1995 链式提升机用环链

이 규격은 체인블록,체인 레버 호이스트, 전기 체인 호이스트 등에 사용하는 링크체인에 대하

Link chain for chain hoists

DIN 73357:1995 柴油发动机用燃油过滤器.旋压过滤器用过滤器盖.法兰横向和纵向安装用固定和连接尺寸

The standard specifies mounting and connecting dimensions of filter heads and mounting flanges for spin-on fuel filters.

Fuel filters for Diesel engines - Filter heads for spin-on filters - Mounting and connecting dimensions for horizontal and vertical flange mounting