共找到 365 条与 砌体结构工程 相关的标准,共 25 页
The document deals with the specification of masonry strength classes on the basis of suitability tests on masonry. A more detailed classification has been made possible by the introduction of further masonry strength classes up to masonry strength class M6. The more precise design method previously specified in DIN 1053-2 has now been included in the new edition of DIN 1053-1.
Masonry - Part 2: Masonry strength classes on the basis of suitability tests
DTU 20.12. Maçonnerie des toitures et d'étanchéité - Gros oeuvre en maçonnerie des toitures destinées à recevoir un revêtement d'étanchéité - Partie 2 : cahier des clauses spéciales.
DTU 20.12 - Maçonnerie des toitures et d'étanchéité - Gros oeuvre en maçonnerie des toitures destinées à recevoir un revêtement d'étanchéité - Partie 1 : cahier des clauses techniques
Specification for mortar for masonry; part 1: rendering and plastering mortar with inorganic binding agents
Specification for mortar for masonry; part 2: masonry mortar
1.1 This test method is intended for testing roller-compacted concrete specimens and covers determination of the relative bond between layers of hardened concrete in multiple-lift forms of construction. It is applicable to all types of layered concrete construction involving an upper layer of concrete or mortar bonded to an underlying layer of concrete or mortar where the total depth is sufficient to meet the minimum specimen length and diameter requirements of this test method. Note 1-This test method does not provide tensile strength results of the material tested. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Determining Bond Strength Between Hardened Roller Compacted Concrete and Other Hardened Cementitious Mixtures Point Load Test
1.1 This guide covers unit sizes for clay and concrete masonry units laid in mortar for use in buildings and building systems designed in accordance with the principles of modular coordination. Specifically it covers: 1.1.1 Sizes of full-size units and supplementary units. 1.1.2 Joint thicknesses. 1.1.3 Specified dimensions. 1.2 Permissible variations from specified dimensions of masonry units vary with intended use, project requirements and type of product. Thus, permissible dimensional variations for masonry units should be obtained from the appropriate ASTM specification. See Section 2 for a listing of appropriate specifications.
Standard Guide for Modular Coordination of Clay and Concrete Masonry Units
Glossary of building and civil engineering terms. Masonry. Terms common to masonry
Methods of test for masonry units; part 15: determination of water vapour permeability of natural stone and autoclaved aerated concrete masonry units
Methods of test for masonry units; part 14: determination of moisture movement of aggregate concrete masonry units
Methods of test for masonry units; part 13: determination of net and gross dry density of masonry units
Methods of test for masonry units; part 12: determination of length change during moisture movement in autoclaved aerated concrete masonry units
Methods of test for masonry units; part 11: determination of water absorption of clay and aggregate concrete masonry units due to capillary action
Methods of test for masonry units; part 10: determination of moisture content of calcium silicate, aggregate concrete and autoclaved areated concrete masonry units
Methods of test for masonry units; part 9: determination of volume of voids and net volume of clay and calcium silicate masonry units by sand filling
Methods of test for masonry units; part 8: determination of water absorption of aggregate concrete masonry units by soaking
Methods of test for masonry units; part 7: determination of water absorption of clay masonry units by boiling in water
Methods of test for masonry units; part 6: determination of bending tensile strength of concrete masonry units
Methods of test for masonry units; part 5: determination of soluble salt content of clay masonry units
Methods of test for masonry units; part 4: determination of real density and bulk density for natural stone masonry units
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号