T11 发动机与附属装置 标准查询与下载

NF R16-319:1992 道路车辆.旋入式喷嘴座,B型、S规格针栓喷嘴用20,21和27型

Road vehicles. Screw-in injection nozzle holders, types 20, 21 and 27 for pintle nozzle size "S", type "B".

NF R16-221:1992 道路车辆.压缩点火发动机用旋压式燃油过滤器.安装和连接尺寸

Road vehicles. Spin-on fuel filters for compression-ignition engines. Mounting and connecting dimensions.

NF R16-340:1992 道路车辆.压燃式发动机.旋入式喷嘴座,24、25和26型

ROAD VEHICLES. COMPRESSION-IGNITION ENGINES. SCREW-IN INJECTION NOZZLE HOLDERS, TYPES 24, 25 AND 26.

NF U10-207:1992 农业用拖拉机.试验规程.第8部分:发动机空气滤清器

AGRICULTURAL TRACTOR. TEST PROCEDURES. PART 8 : ENGINE AIR CLEANER.

GM 9985888-1992 半合成锂润滑脂

For gummiartiklar dar speciella krav stallsgummits tojningsegenskaper.

Grease, Lithium, Semisynthetic

GM 9981873-1992 钣金水溶性拉丝润滑剂

Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein.

Drawing Compounds - Water Dilutable, for Aluminum Sheet Revision C

GM 9985360-1992 玻璃钢聚氨酯分为两个部分胶粘剂

Freigabemuster, für die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung genehmigt sein, ehe eine Lieferung erfolgen kann. Bei beabsichtigter Abweichung von dieser Vorschrift oder von den bisher frei

Adhesive,Two-Part, Urethane, FRP Revision C

GM 9985838-1992 氨基甲酸乙酯树脂分为两部分粘合剂.取代 GMNA 9982187,GMNA 9982187

Muster von Formmassen bzw. Werden, ehe die Lieferung aufgrund dieser Muster aufgenommen wird.

Adhesive, Two-Part, Urethane, Resin Revision A [Replaced: GMNA 9982187]

GM 9985824-1992 玻璃钢聚氨酯分为两个部分粘合剂

Angivna materialfordringar overensstammer med de som anges I SS 141774, utgava 4.

Adhesive, Two-Part, Polyurethane, FRP Revision A

GM 9985454-1992 玻璃钢聚氨酯分为两个部分粘合剂

Unbeschodet etwaiger durch den Abnehmer erfolgenden Stic)iprobenprüfungen tragt der Lieferant die Verantwortung dofYi, do13 die gelieferte Ware die Opel -Zeichnungrvorschrifttsn erfüllt. Mustern sowie Teilen einer ersten Serienlieferung unaufgefordert e

Adhesive, Two-Part, Urethane, FRP Revision D

GM 9985745-1992 泵送抗颤振扩大粘合剂.取代 GMNA 9981264,GMNA 9981264,GMNA 9985021,GMNA 9985021

Tech n. Lief e rbedi n g ungen für Werkstoffe

Adhesive, Anti-Flutter Expanding, Pumpable [Replaced: GMNA 9981264]

GM 9985760-1992 玻璃钢-测绘局聚氨酯分为两个部分粘合剂

Samples of components or material released to this specification shall be tested for conformity with the requirements of this specification and approved by Product Engineering Department prior to commencement of delivery of bulk supplies.

Adhesive, Two-Part, Urethane, FRP-SMC Revision A

GM 9985758-1992 氨基甲酸乙酯树脂分为两个部分粘合剂

Samples of components or material released to this specification shall be tested for conformity with the requirements of this specification and approved by Product Engineering Department prior to commencement of delivery of bulk supplies.

Adhesive, Two-Part, Urethane, Resin Revision A

WJ 1261-1992 发动机熄火装置（限用标准）

Engine stop device (restricted standard)

GM 9985806-1991 丙烯酸分为两个部分粘合剂

There is no equivalent in either Swedish or foreign standards of cast iron, in accordance with this standard.

Adhesive, Two-Part, Acrylic

ISO 8123:1991 道路车辆 起动电机径节小齿轮

Specifies the diametral pitches, pressure angles, number of teeth and other tooth characteristics which are necessary to ensure interchangeability of pinions used for starter motors mounted on reciprocating internal combustion engines for road vehicles.

Road vehicles; diametral pitch starter motor pinions

GM 9984834-1991 表面元件非导电密封底漆粉末

Only the latest approved standards are applicable unless otherwise specified.

Primer, Powder, Nonconductive Porosity Sealing for SMC

GM 9984835-1991 表面元件导电密封底漆粉末

In diesen Technischen Lieferbedingungen sind die qualitatsabhangigen Anforderungen dieses Polsterstoffes festgelegt. Die allgemeinen Mindestanforderungen sind grundsatzlich nach TM 110000 zu prufen.

Primer, Powder, Conductive Porosity Sealing for SMC

SAE J342-1991 大型发动机用火花熄灭器试验程序

This SAE Recommended Practice establishes equipment and procedures for the evaluation of the effectiveness and other performance characteristics of spark arresters or turbochargers used on the exhaust system of large engines normally used in a railroad locomotive, stationary power plant, and other similar applications. This document does not cover applications requiring flame arresting, exhaust gas cooling, or isolation from explosive gases. Two test methods are presented; a laboratory test using ambient air (cold test) and an engine test using exhaust gases (hot test). The hot test is preferred.

Spark Arrester Test Procedure for Large Size Engines

GM 9985649-1990 泵送热熔封闭细胞扩大密封

For stomljudsdampning, t ex hjulhus. Appliceras lutande/vertikala ytor, samt undersida av horisontellaytor. Ytorna kan vara bade formade och plana.

SEALER, EXPANDING, CLOSED CELL, HOT MELT, PUMPABLE