共找到 102 条与 航天用起爆点火装置 相关的标准,共 7 页
Spark Igniter Gap Types
Spark Igniter Gap Types
Shipping Configuration - l i n e 1: Delete Drawing Num-ber 30003-35668223 and add Drawing Number 30003-356AS200.
LAUNCHER, ROCKET, AIRBORNE, LAU 61A/A
Spark Plug, Aircraft Reciprocating Engine [Superseded: SAE ARP 247]
Spark Plug, Aircraft Reciprocating Engine [Superseded: SAE ARP 247]
This specification covers a dual purpose, airborne, external store type, rocket launcher capable of shipping, storing and launching nineteen 2.75 inch Folding Fin Aircraft Rockets (FFAR). This launcher is used in two configurations as follows:
LAUNCHER, ROCKET, AIRBORNE, LAU 61A/A
%he specification covers Belay Element, Cartridge: XM44 Assembly, for use in cartridges for propellant actuated deeces I n aircrew emergency escape systems
DELAY ELEMENT, CARTRIDGE, XM44 ASSEMBLY
This specification covers Delay Element, Cartridge: XMl7, for use in cartridges for propellant actuated devices 'in aircrew emergency escape systems.
DELAY ELEMENT, CARTRIDGE, XM17 ASSEMBLY
The equipment covered by this specification shall be capable of transferring stored energy t o a maximum of ten e l e c t r i c a l destruct igniters located i n electronic equipments within a vehicle.
INITIATOR, DESTRUCT IGNITER MX-8278(*)/ASQ
This amendment forms a part of Military Specification MIL-23951(Wep), dated i9 August 1964, and has been approved by the Naval Air Systems Command, Department of the- Navy.
IGNITION MATERIAL, PELLETED, PYROTECHNIC
This standard provides a listing of the spark plug models which have been found suitable as calibration spark plugs for use in the SAE 17.6 cu in. spark-plug-rating engine (AS 840).
Calibration Spark Plugs
This specification establishes the qualification and acceptance limits for aeronautical engine low tension spark igniters.
Igniter, Spark, Aeronautical Engine (Low Tension)
MARKING SHALL BE RAISED AT LEAST .O30 AND CONSPICUOUSLY PAINTED.
TRANSMITTERS, PRESSURE, SYNCHRO, AIRCRAFT, 165 DEGREE MOVEMENT
The purpose of these specifications is to provide a standard procedure and standard equipment for the evaluation of a measurement of the ionization voltage (sparking voltage) of shunted surface gap spark igniter designs. These specifications contain general information pertaining to the sparking voltage parameter of shunted surface gap spark igniters; test equipment circuitry; bill of materials for test equipment; test equipment operation.
Low Tension Spark Igniter Sparking Voltage Test
This specification defines the minimum requiremenis for one type of pelleted pyrotechnic ignition material.
IGNITION MATERIAL, PELLETED, PYROTECHNIC
This amendment forms a part of Military Specification MIL-1-23488 (Wep) of 19 October 1962, and has been approved by the Bureau of Naval Weapons, Department of the Navy.
IGNITION ELEMENT, ELECTRIC, MARK 10 MOD 6
This mendrfient form a part of Xi1ita-y Ssecification &EL-L-21910(AER) dated i5 February 1959 znà hzs-Seen apgroveà by the Bureau of Eaval Weqons, Depmtrnent of the Navy.
LAUNCHER, ROCKET LAU-10/A
This specification establishes the requirements for shielded, detachable high tension spark plug leads for reciprocating engines. The leads shall be of the following grades for use in the stipulated temperature range: Grade - A 250 to -35F. Grade - B 450 to -65F.
Leads, Shielded, High Tension, Detachable Spark Plug
This specification covers the general requirements for equipment used on aircraft to suspend and launch missiles, sonobuoys, bombs, marine location markers, rockets, aircraft parachute flares, torpedoes, underwater sound signals, aircraft depth bombs, bathythermographs, depth charges, etc. This specification also covers items of equipment used to operate and control the operation of the launching equipment, but does not cover items of equipment used to compute the launching point.
LAUNCHER, WEAPONS, AIRBORNE AND ASSOCIATED EQUIPMENT, GENERAL SPECIFICATION FOR
This specification governs the manufacture, assembly and preparation for delivery of the Ignition Element, Electric, Mark 10 Mod O, and the methods of inspection and tests upon which product acceptance w i l l be based.
IGNITION ELEMENT, ELECTRIC, MARK 10 MOD 6
es the only classification covered by.this specification. Seo = Thisipecification cove& the requirementz for the
IGNITER, MARK 188 MOD 0
This drawing describes device requirements for class B microcircuits in accordance with 1.2.1 of MIL-STD-883, 4aProvisions for the use of MIL-STD-883 in conjunction with conpliant non-JAN devices.#'
LAUNCHER, ROCKET LAU-10/A
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号