Y26 日用搪瓷制品 标准查询与下载

BS EN ISO 28764:2011 釉瓷和搪瓷 钢板,铝板和铸铁上瓷釉测试的样本生产

This International Standard specifies a method for the production of specimens suitable for testing vitreous and porcelain enamel coatings. It specifies two different specimens: ? specimens taken from production articles; ? specially produced specimens. NOTE Only the specially produced specimens can be used when the loss in mass per unit area of the enamel coating is to be determined quantitatively, as specimens cut from enamelled articles can reduce the accuracy of the test method.

Vitreous and porcelain enamels. Production of specimens for testing enamels on sheet steel, sheet aluminium and cast iron

BS EN ISO 28763:2011 釉瓷和搪瓷.空气与气体和气体与气体热交换器用交流换热,上釉和包装的板材.规格

This International Standard specifies the minimum requirements and the functional characteristics of enamel coatings applied by any process, such as wet dipping, wet flow-coating, wet spraying, wet electrostatic spraying, wet electrodeposition or dry-powder electrostatic spraying, to profiled steel heat exchanger panels in regenerative heat exchangers, before and after packing in baskets. For very severe service conditions, or to obtain extended operational life, more stringent limits may be agreed between customer and supplier.

Vitreous and porcelain enamels. Regenerative, enamelled and packed panels for air-gas and gas-gas heat exchangers. Specifications

DIN EN ISO 4534:2011 釉瓷和搪瓷.流动性的测定.熔化液流试验(ISO 4534-2010);德文版本EN ISO 4534-2010

This document specifies a comparative method of determining the fluidity behaviour of vitreous and porcelain enamels in the viscous condition during firing. It is not intended for use as an absolute method.

Vitreous and porcelain enamels - Determination of fluidity behaviour - Fusion flow test (ISO 4534:2010); German version EN ISO 4534:2010

BS ISO 6370-1:2011 釉瓷和搪瓷.耐磨性的测定.磨损试验装置

Vitreous and porcelain enamels. Determination of the resistance to abrasion. Abrasion testing apparatus

BS ISO 6370-2:2011 釉瓷和搪瓷.耐磨性的测定.表层磨损后的质量损失

Vitreous and porcelain enamels. Determination of the resistance to abrasion. Loss in mass after sub-surface abrasion

ASTM F1178-11 金属连接件和家具上釉系统性能及烘焙的标准规格

1.1 This specification covers the performance of a baking primer and enamel on metal for use on fabricated metal products, including marine furniture and joiner work. 1.2 The values stated in inch-pound units are to be regarded as standard. The metric (SI) units, given in parentheses, are for information only. 1.3 Painting facilities shall comply with all applicable Federal and State regulations regarding emissions and waste disposal. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Performance of Enameling System, Baking, Metal Joiner Work and Furniture

ISO 28762:2010 釉瓷和搪瓷.书写板用钢的搪瓷层.规范

WARNING — This International Standard calls for the use of substances and/or procedures that may be injurious to health if adequate safety measures are not taken. This International Standard does not address any health hazards, safety or environmental matters associated with its use. It is the responsibility of the user of this International Standard to establish appropriate health, safety and environmentally acceptable practices and take suitable actions for any national and international regulations. Compliance with this International Standard does not in itself confer immunity from legal obligations. This International Standard specifies the requirements for the functional and aesthetic characteristics of vitreous and porcelain enamel coatings applied to plain steel, for use as writing surfaces (whiteboards and chalkboards).

Vitreous and porcelain enamels - Enamel coatings applied to steel for writing surfaces - Specification

NF A92-129*NF EN 15771:2010 釉瓷和搪瓷.按照莫氏硬度标进行表面划痕硬度的测定

Vitreous and porcelain enamels - Determination of surface scratch hardness according to the Mohs scale.

DIN EN 15826:2010 釉瓷和搪瓷.术语.德文版本EN 15826-2009

This document defines a number of terms relating to vitreous and porcelain enamels and their technology. The list of these terms is not complete and only comprises those terms for which the definition is considered necessary for correct and adequate understanding in order to clarify these processes.

Vitreous and porcelain enamels - Terminology; German version EN 15826:2009

BS EN 15826:2009 玻璃釉和陶瓷釉.术语

This European Standard defines a number of terms relating to vitreous and porcelain enamels and their technology. This list is not complete and only comprises those terms for which the definition is considered necessary for correct and adequate understanding in order to clarify these processes. It should be understood that the interpretations given are those corresponding to the practical usage in this field and that they do not necessarily coincide with those used in other fields. For purposes of clarification, the term Vitreous Enamel, used throughout this European Standard, is synonymous with Porcelain Enamel, the term favoured in the United States and some other countries.

Vitreous and porcelain enamels - Terminology

SN/T 0872-2010 进出口日用搪瓷制品检验规程

本标准规定了进出口日用搪瓷制品的抽样、检验、结果判定和不合格处置。 本标准适用于薄钢板制造的进出口日用搪瓷制品的检验。 本标准不适用于铸铁搪瓷的检验。

Rules for the inspection of domestic enamelware for import and export

ASTM C282-10(2015) 搪瓷耐强酸腐蚀的标准试验方法 (柠檬酸斑点试验)

3.1 This test method is intended specifically for testing the porcelain enamel finish on stoves, refrigerators, table tops, sinks and other sanitary ware, laundry appliances, architectural units, etc., where the surface may come in contact with food acids at room temperature. 3.2 Citric acid has been chosen as the test medium because it is one of the most common of the food acids and will generally provide a measurable result in its action on porcelain enamel. 1.1 This test method covers a procedure for evaluating porcelain enamels in their resistance to citric acid exposure at room temperature. No attempt is made to categorize porcelain enamels as to their acid-resistance or non acid-resistance properties, since the requirements in the several branches of the industry differ. 1.2 The test method is applicable for ware of various shapes providing they contain a substantially flat area approximately 50 mm in diameter. 1.3 The test method is not applicable to finishes on chemical and hospital ware, which may come in contact with strong mineral acids, nor to cooking utensils, which may come in prolonged contact with hot acid solutions. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Acid Resistance of Porcelain Enamels(Citric Acid Spot Test)

ASTM C285-10(2015)e1 湿磨和干磨搪瓷粉的筛选分析标准试验方法

3.1 The fineness of the frit has a direct bearing on many of its properties, such as fusibility, tearing, gloss, opacity, suspension in the slip, and ease of spraying. 1.1 These test methods cover the determination of the fineness of frit in wet- or dry-milled porcelain enamels and other ceramic coatings for metals by means of the No. 200 (75-μm) or No. 325 (45-μm) sieve. 1.2 The two methods appear as follows:   Sections   8199;8199;8199;Method A—Referee Method 8199;8199;8199;Method B—Routine Method  4 to 9  10 to 14 1.3 Method A is intended for use where a referee method of higher accuracy is required, while Method B is intended to meet the needs of normal enamel plant production control operations where a rapid, simplified method of sieve testing is required. The accuracy of the simplified method has proved to be entirely adequate for this use. The simplified test, however, is not recommended where high accuracy is required. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Sieve Analysis of Wet-Milled and Dry-Milled Porcelain Enamel

ASTM C282-10 搪瓷耐酸的标准试验方法(柠檬酸斑点试验)

This test method is intended specifically for testing the porcelain enamel finish on stoves, refrigerators, table tops, sinks and other sanitary ware, laundry appliances, architectural units, etc., where the surface may come in contact with food acids at room temperature. Citric acid has been chosen as the test medium because it is one of the most common of the food acids and will generally provide a measurable result in its action on porcelain enamel.1.1 This test method covers a procedure for evaluating porcelain enamels in their resistance to citric acid exposure at room temperature. No attempt is made to categorize porcelain enamels as to their acid-resistance or non acid-resistance properties, since the requirements in the several branches of the industry differ. 1.2 The test method is applicable for ware of various shapes providing they contain a substantially flat area approximately 50 mm in diameter. 1.3 The test method is not applicable to finishes on chemical and hospital ware, which may come in contact with strong mineral acids, nor to cooking utensils, which may come in prolonged contact with hot acid solutions. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Acid Resistance of Porcelain Enamels (Citric Acid Spot Test)

ASTM C872-10 从搪瓷表面析出铅及镉的标准试验方法

The determination of lead and cadmium release from porcelain enamel surfaces was formerly of interest only to manufacturers of porcelain enamel cookware and similar food service products. Food contact surfaces of these container-type products have been evaluated using a test procedure similar to Test Method C738. Recently, however, there has been a need to measure lead and cadmium release from flat or curved porcelain enamel surfaces that are not capable of being evaluated by a test similar to Test Method C738.1.1 This test method covers the precise determination of lead and cadmium extracted by acetic acid from porcelain enamel surfaces. 1.2 Values stated in SI units are to be regarded as the standard. Inch-pound units are given for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Lead and Cadmium Release from Porcelain Enamel Surfaces

DIN EN ISO 4528:2009 釉瓷和搪瓷精饰 制件的釉瓷和搪瓷区域用试验方法的选择

This International Standard is a guide to the selection of test methods for evaluating the performance of vitreous and porcelain enamelled finishes in different applications. It references the test methods available for measuring the properties of these finishes, and correlates these properties to requirements of specific enamelled articles. It is limited for the most part to test methods that are described in ISO International Standards and does not provide acceptance criteria or performance limits for the properties. This International Standard applies to all enamelled articles irrespective of their basis metals.

Vitreous and porcelain enamel finishes - Selection of test methods for vitreous and porcelain enamelled areas of articles (ISO 4528:2000); English version of DIN EN ISO 4528:2009-04

DIN EN ISO 13805:2009 铝用釉瓷和搪瓷 在电解液作用下测定铝上瓷层附着力(剥落试验)

This International Standard specifies a test method for the accelerated determination of the resistance of porcelain enamel coatings on aluminium and aluminium alloys to spalling as a result of exposure to moisture or weathering. Because spalling is caused by the lack of adhesion between the coating and the base metal, the spall test is a test of adhesion. The greater the extent of spalling in this test, the greater the likelihood that the article will spall in service.

Vitreous and porcelain enamels for aluminium - Determination of the adhesion of enamels on aluminium under the action of electrolytic solution (spall test) (ISO 13805:1999); English version of DIN EN ISO 13805:2009-04

DIN EN ISO 13807:2009 釉瓷和搪瓷 化学工业用瓷层热冲击试验中裂纹形成温度的测定

This International Standard specifies a test method for the determination of the crack formation temperature of enamels for the chemical industry by subjecting enamelled steel specimens to thermal shock using cold water. The value of the crack formation temperature measured according to this test method is not valid for the finished component (see annex A). It is a parameter of vitreous and porcelain enamels for comparing the relative quality of different enamel formulations.

Vitreous and porcelain enamels - Determination of crack formation temperature in the thermal shock testing of enamels for the chemical industry (ISO 13807:1999, including Cor 1:2000); English version of DIN EN ISO 13807:2009-04

DIN 51176-2:2008 釉和搪瓷.缺陷的表达和描述.第2部分:薄膜涂层

Vitreous and porcelain enamels - Presentation and characterization of defects - Part 2: Thin-film coats

DIN EN 15206:2007 釉瓷和搪瓷.薄钢板、薄铝板和铸铁上搪瓷的测试用试样制备

This European Standard specifies a method for the production of specimens suitable for testing vitreous and porcelain enamel coatings. The standard specifies 2 different specimens: - specimens taken from production article, and - specially produced specimens. NOTE Only the specially produced specimens can be used when the loss in mass per unit area of the enamel coating is to be determined quantitatively as specimens cut from enamelled articles can reduce the accuracy of the test method.

Vitreous and porcelain enamels - Production of specimens for testing enamel on sheet steel, sheet aluminium and cast iron; German version EN 15206:2007