TS 61000-3-5 CORR 2-2010
Electromagnetic compatibility (EMC) – Part 3-5: Limits – Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 75 A CORRIGENDUM 2 (Edition 2.0)

Compatibilité électromagnétique (CEM) – Partie 3-5: Limites – Limitation des fluctuations de tension et du flicker dans les réseaux basse tension pour les équipements ayant un courant appelé supérieur à 75 A CORRIGENDUM 2 (Edition 2.0)

TS 61000-3-5 CORR 2-2010 发布历史

This section of IEC 1000-3 is concerned with the emission of disturbances due to voltage fluctuations and flicker.The recommendations in this Technical Report are applicable to electrical and electronic equipment intended to be connected to a public low-voltage a.c. distribution system@ where the equipment has a rated input current exceeding 16 A per phase@ or has a lower rated current@ but requires the special consent of the supply authority.The recommendations that specify the information required to enable a supply authority@ manufacturer@ or consumer to assess equipment and appropriate questionnaires are included as annexes A and B.Guidance is also given on emission values of voltage fluctuations produced by equipment which has been type tested to the specified conditions given in IEC 1000-3-3.NOTE 1 - The limits recommended in this report are mainly based on the subjective severity of the flicker of the light output from 230 V/60 W coiled-coil filament tamps as a result of fluctuation of the supply voltage. For systems with nominal voltages less than 220 V@ line-to-neutral@ limits@ and reference circuit values have not yet been considered.The authorization to connect equipment to the supply depends on the levels of disturbance caused by the equipment and the load flow conditions in the network.NOTE 2 - For equipment requiring authorization@ only general recommendations for the assessment of disturbances can be given. There is no guarantee that the connection of equipment complying with the recommendations in clause 3 will be allowed in all cases@ as system loading must not exceed plant ratings (transformers@ cables@ etc.).The methods of assessment may be applied also to private consumer installations.

TS 61000-3-5 CORR 2-2010由IEC - International Electrotechnical Commission 发布于 2010-05-01，并于 2010-08-30 实施。

TS 61000-3-5 CORR 2-2010的历代版本如下：

• 2010年05月01日 TS 61000-3-5 CORR 2-2010 Electromagnetic compatibility (EMC) – Part 3-5: Limits – Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 75 A CORRIGENDUM 2 (Edition 2.0)

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 TS 61000-3-5 CORR 2-2010 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

TS 61000-3-5 CORR 2-2010

发布日期

2010年05月01日

实施日期

2010年08月30日

废止日期

无

中国标准分类号

/

国际标准分类号

/

发布单位

IEC - International Electrotechnical Commission

引用标准

1

适用范围

This section of IEC 1000-3 is concerned with the emission of disturbances due to voltage fluctuations and flicker.The recommendations in this Technical Report are applicable to electrical and electronic equipment intended to be connected to a public low-voltage a.c. distribution system@ where the equipment has a rated input current exceeding 16 A per phase@ or has a lower rated current@ but requires the special consent of the supply authority.The recommendations that specify the information required to enable a supply authority@ manufacturer@ or consumer to assess equipment and appropriate questionnaires are included as annexes A and B.Guidance is also given on emission values of voltage fluctuations produced by equipment which has been type tested to the specified conditions given in IEC 1000-3-3.NOTE 1 - The limits recommended in this report are mainly based on the subjective severity of the flicker of the light output from 230 V/60 W coiled-coil filament tamps as a result of fluctuation of the supply voltage. For systems with nominal voltages less than 220 V@ line-to-neutral@ limits@ and reference circuit values have not yet been considered.The authorization to connect equipment to the supply depends on the levels of disturbance caused by the equipment and the load flow conditions in the network.NOTE 2 - For equipment requiring authorization@ only general recommendations for the assessment of disturbances can be given. There is no guarantee that the connection of equipment complying with the recommendations in clause 3 will be allowed in all cases@ as system loading must not exceed plant ratings (transformers@ cables@ etc.).The methods of assessment may be applied also to private consumer installations.