BS 6001-9-2002
计数取样检验程序.分批检验时控制出厂质量的以信任为基础的零抽样验收计划已作废

Sampling procedures for inspection by attributes - Double sampling plans using minimal sample sizes, indexed by producer's risk quality (PRQ) and consumer's risk quality (CRQ)

BS 6001-9-2002 发布历史

This British Standard provides double sampling plans by attributes for the acceptance inspection of lots of discrete items. The plans are indexed by the producer's risk quality (PRQ) and the consumer's risk quality (CRQ) where the nominal risks are either 5 % or 10 %. Plans are provided for inspection for percent nonconforming and for inspection for nonconformities per 100 items. The lot is acceptable if there are no nonconforming items (nonconformities) in the first random sample, and not acceptable if it contains two or more nonconforming items (nonconformities). If precisely one nonconforming item is found in the first sample, a second random sample is drawn; the lot is then acceptable if the second sample contains no nonconforming items (nonconformities) and not acceptable otherwise. The objective of this standard is to provide procedures that enable lot disposition to be determined quickly and economically if quality is particularly good or bad. For intermediate quality a second sample is drawn in order to be able to discriminate more reliably between acceptable and unacceptable lots. The two sample sizes are chosen to minimize the maximum expected sample size with respect to incoming quality subject to the nominal risks not being exceeded. Similarly, the plans may be used to test the hypothesis that a lot or process quality level is equal to the PRQ (i.e. acceptable) against the alternative hypothesis that the quality level is equal to the CRQ (i.e. unacceptable). The plans are preferable to single sampling plans where the cost of inspection is high, where the delay and uncertainty caused by the possible requirement for second samples is inconsequential and where a relatively large ratio of the consumer's risk quality to the producer's risk quality can be tolerated. The plans are suitable for isolated lots or for short series of lots, where the sum of the two sample sizes is no larger than about 10 % of the size of the lot. The plans are also suitable for continuing series of lots when lots that fail to satisfy the acceptance criteria are 100 % inspected and all nonconforming items replaced by conforming items: however, for continuing series of lots, consideration should also be given to using double sampling plans from BS 6001-1.

BS 6001-9-2002由英国标准学会 GB-BSI 发布于 2002-09-20，并于 2002-09-20 实施，于 2011-04-30 废止。

BS 6001-9-2002 在中国标准分类中归属于: A00 标准化、质量管理，在国际标准分类中归属于: 03.120.30 统计方法的应用。

BS 6001-9-2002的历代版本如下：

• 2002年09月20日 BS 6001-9-2002 计数取样检验程序.分批检验时控制出厂质量的以信任为基础的零抽样验收计划

BS 6001-9-2002 计数取样检验程序.分批检验时控制出厂质量的以信任为基础的零抽样验收计划 于 2011-04-30 变更为 BS ISO 28801-2011 厂方风险质量(PRQ)和消费者风险质量(CRQ)索引,采用最少样本量属性的二重抽样计划(CRQ)。

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 BS 6001-9-2002 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

BS 6001-9-2002

发布日期

2002年09月20日

实施日期

2002年09月20日

废止日期

2011-04-30

中国标准分类号

A00

国际标准分类号

03.120.30

发布单位

GB-BSI

代替标准

BS ISO 28801-2011

适用范围

This British Standard provides double sampling plans by attributes for the acceptance inspection of lots of discrete items. The plans are indexed by the producer's risk quality (PRQ) and the consumer's risk quality (CRQ) where the nominal risks are either 5 % or 10 %. Plans are provided for inspection for percent nonconforming and for inspection for nonconformities per 100 items. The lot is acceptable if there are no nonconforming items (nonconformities) in the first random sample, and not acceptable if it contains two or more nonconforming items (nonconformities). If precisely one nonconforming item is found in the first sample, a second random sample is drawn; the lot is then acceptable if the second sample contains no nonconforming items (nonconformities) and not acceptable otherwise. The objective of this standard is to provide procedures that enable lot disposition to be determined quickly and economically if quality is particularly good or bad. For intermediate quality a second sample is drawn in order to be able to discriminate more reliably between acceptable and unacceptable lots. The two sample sizes are chosen to minimize the maximum expected sample size with respect to incoming quality subject to the nominal risks not being exceeded. Similarly, the plans may be used to test the hypothesis that a lot or process quality level is equal to the PRQ (i.e. acceptable) against the alternative hypothesis that the quality level is equal to the CRQ (i.e. unacceptable). The plans are preferable to single sampling plans where the cost of inspection is high, where the delay and uncertainty caused by the possible requirement for second samples is inconsequential and where a relatively large ratio of the consumer's risk quality to the producer's risk quality can be tolerated. The plans are suitable for isolated lots or for short series of lots, where the sum of the two sample sizes is no larger than about 10 % of the size of the lot. The plans are also suitable for continuing series of lots when lots that fail to satisfy the acceptance criteria are 100 % inspected and all nonconforming items replaced by conforming items: however, for continuing series of lots, consideration should also be given to using double sampling plans from BS 6001-1.

BS 6001-9-2002系列标准