ISO 10360-5-2010
产品几何量技术规范(GPS).坐标测量机(CMM)的验收和复检试验.第5部分:使用单个和多触针探测系统的坐标测量机

Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 5: CMMs using single and multiple stylus contacting probing systems

ISO 10360-5-2010 发布历史

This part of ISO 10360 specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs using -any type of contacting probing system, -a discrete point probing mode, and -spherical or hemispherical stylus tip(s). It complements ISO 10360-7, which is the module for CMMs with video probing systems, and ISO 10360-2, which is universal, i.e. not probe-type specific. NOTE It is the CMM probing performance tests which are specified by the maximum permissible errors (MPEs), due to the impracticality of isolating the performance of the probing system from that of the CMM, even on a small artefact such as a test sphere. This part of ISO 10360 applies to CMMs supplied with any of the following: a) single-stylus probing system; b) multi-stylus probing systems with fixed multiple styli attached to a single probe (e.g. “star” stylus); c) multiple probing systems such as those with a stylus for each of their probes; d) systems with articulating probing; e) stylus and probe changing systems; f) manual (non-driven) CMMs. This part of ISO 10360 is not applicable to non-contacting probing systems, which require different testing procedures. The terms “multi-stylus size error”, etc., should strictly be written “combined CMM and multi-stylus probingsystem size error”, etc. For convenience, the wording has been truncated. If it is desired to isolate the probing-system performance as far as is practical, the influence of the CMM can be minimized. See Annex C for more information.

ISO 10360-5-2010由国际标准化组织 IX-ISO 发布于 2010-09-15，并于 2010-09-15 实施。

ISO 10360-5-2010 在中国标准分类中归属于: N12 流量与物位仪表，在国际标准分类中归属于: 17.040.30 测量仪器仪表。

ISO 10360-5-2010 发布之时，引用了标准

• ISO 10360-1-2000 产品几何量技术规范(GPS) 坐标测量机(CMM)的验收和复检试验 第1部分:词汇 两种语言版
• ISO 10360-2-2009 产品几何技术规范(GPS).坐标测量机(CMMs)的验收和复检.第2部分:用于测量线性尺寸规格的CMMs
• ISO 14253-1 产品几何量技术规范(GPS).工件的测量检验和测量设备.第1部分:按规范检验一致性或不一致性的判定规则
• ISO/IEC Guide 99 计量学的国际词汇.基本与一般概念与相关术语(VIM)

ISO 10360-5-2010的历代版本如下：

• 2000年12月 ISO 10360-5-2000 产品几何量技术规范(GPS) 坐标测量机(CMM)的验收和复检试验 第5部分:使用多触针探测系统的坐标测量机
• 2010年09月15日 ISO 10360-5-2010 产品几何量技术规范(GPS).坐标测量机(CMM)的验收和复检试验.第5部分:使用单个和多触针探测系统的坐标测量机
• 2020年03月31日 ISO 10360-5-2020 几何产品规范（GPS）.坐标测量系统（CMS）的验收和再鉴定试验.第5部分:使用离散点和/或扫描测量模式的单触针和多触针接触探测系统的坐标测量机（CMM）（ISO 10360-5-2020）

ISO 10360-5-2010 产品几何量技术规范(GPS).坐标测量机(CMM)的验收和复检试验.第5部分:使用单个和多触针探测系统的坐标测量机 由 ISO/PAS 12868-2009 变更而来。

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 ISO 10360-5-2010 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

ISO 10360-5-2010

发布日期

2010年09月15日

实施日期

2010年09月15日

废止日期

无

中国标准分类号

N12

国际标准分类号

17.040.30

发布单位

国际标准化组织

适用范围

This part of ISO 10360 specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs using -any type of contacting probing system, -a discrete point probing mode, and -spherical or hemispherical stylus tip(s). It complements ISO 10360-7, which is the module for CMMs with video probing systems, and ISO 10360-2, which is universal, i.e. not probe-type specific. NOTE It is the CMM probing performance tests which are specified by the maximum permissible errors (MPEs), due to the impracticality of isolating the performance of the probing system from that of the CMM, even on a small artefact such as a test sphere. This part of ISO 10360 applies to CMMs supplied with any of the following: a) single-stylus probing system; b) multi-stylus probing systems with fixed multiple styli attached to a single probe (e.g. “star” stylus); c) multiple probing systems such as those with a stylus for each of their probes; d) systems with articulating probing; e) stylus and probe changing systems; f) manual (non-driven) CMMs. This part of ISO 10360 is not applicable to non-contacting probing systems, which require different testing procedures. The terms “multi-stylus size error”, etc., should strictly be written “combined CMM and multi-stylus probingsystem size error”, etc. For convenience, the wording has been truncated. If it is desired to isolate the probing-system performance as far as is practical, the influence of the CMM can be minimized. See Annex C for more information.

ISO 10360-5-2010系列标准

谁引用了ISO 10360-5-2010 更多引用